The 10 Scariest Things About Repair Car Keys

How to Repair Car Keys

Car keys might seem tiny and insignificant, but they are crucial to the functioning of your vehicle. The cost of replacing an old or modern transponder car key can range from $200 to upwards of $200.

There are methods to fix your car keys at home for only a fraction of the cost. This article will go over some of the most common car keys problems and the DIY solutions.

Dead Key Fob Battery

Cars come with a remote key fob that allows opening the doors and trunk easier than ever before. However, the battery inside the device could die. There are some tricks you can employ to fix this problem quickly.

First, make sure that the car is still in ignition mode. If it is, then the key car repair fob battery may be drained instead of dead. To test, press the button on the fob against the ignition button on the vehicle. If this works, then the battery is probably in good condition and will only need to be changed.

To replace the fob's battery, first pry the case open using an instrument like a screwdriver, or watch-type tool. Don't apply too much force, as this could cause the fob's casing to split. If the fob isn't coming open with ease, try placing your pry tool in several places on the outside of the case.

Once the fob is opened, remove the mechanical key, and then open the electronic section of the car remote key fob repair. Then, insert the battery replacement and then snap the shell back together. If your key fob does not work after this, it could be an problem with the remote start system of your car. This requires an expert to determine the cause. If this is the case, a trusted mechanic should be able assist you. You can also contact roadside assistance to assist with your vehicle in case you need it.

Broken Key Ring

If your key fob won't work because the ring is broken, there are a few things you might try. Look to see if can locate the broken piece inside the ignition. If it is, you should remove it without damaging the lock on the ignition or door lock. If you have trouble taking it off, call an expert locksmith. They have tools that allow you to safely remove keys that are damaged from the ignition.

A broken car key could also be the result of corrosion of the plastic frame or circuit board. Clean the board with cotton swab. This will eliminate corrosion and ensure the contact pads aren't damaged.

You can repair a damaged ring using a strong wire or nail to close the hole. You can also use superglue to repair a broken ring. First, clean the damaged ring with a damp cloth and then apply a small amount of superglue on each end of the wire or nail. Allow the pieces to dry, and then press them into place. These DIY solutions may sound appealing, however they are only a temporary solution. For long-term repairs, it's best to hire an experienced locksmith. They have the tools and expertise to repair a damaged car key quickly and effectively. They can even replace the battery on your mobile key repair near me fob, and change it's programming if required.

Broken Key Blade

Some key blades might break due to wear and tear. If this occurs, you ought to buy a new one. This problem isn't nearly as serious as you believe at first. The main problem is that the metal blade broke off from the case.

Spraying lubricant into the keyhole is a solution to fix it. Then, you can make use of pliers or tweezers grab the broken end of the key and pull it. If the key is magnetic, you could also try using a magnet to help pull it out. Be careful not to use a magnetic tool on an ignition key as it could cause the tumbler in the lock to break.

If you're not able to remove the broken piece from the key, contact a locksmith right away. They have special tools that let them safely remove keys without causing further damage.

You can also use super glue to fix a broken key. Apply a small amount of glue to the edges and press them in. Wait until the glue has dried before you insert your key into the lock. However, this method isn't reliable and you might have repeat the process several times before it is successful. Plus the super glue might not be enough to keep the key in place. This is more of a temporary solution than a permanent solution.

Broken Plastic Loop

If the plastic loop on your key fob is damaged, it can make the key ineffective. Luckily, this is an simple fix. For a replacement alternative, you can use wire that is thick or a finishing nail. Drill two holes into the broken plastic loop at each end of the wire or nail. Cut the nail or wire to key width and put a drop of superglue in each hole. Then, press the wire or nail into the holes to seal them and allow it to dry.

A locksmith who sells replacement shells is an alternative option. They can transfer the programmable portion of your key to the new shell, and then cut an entirely new blade at less than the cost.

This isn't the most efficient solution, but will allow you to travel once more if your key broken in half. It can be difficult to repair if the key blade is in the ignition however. If you are not careful you can use a hair clip or a needle to take the broken part from the ignition. Get a locksmith equipped with special tools to safely remove damaged keys from ignitions. You can also have a new key made with the proper cuts to fit the ignition of your car.

Broken Master Key

You'll need to try at regaining the key before it becomes completely destroyed. You can make use of lubricants, tweezers, and needle nose pliers for grabbing the fragments of a damaged key repair service.

Spray the inside of your lock with WD-40 or a graphite powder. You may also try the hacksaw method, which involves gently moving the blade down the side of the broken key, and hooking onto some of the 'teeth'. If you are able to do this you should be able remove the broken key from the lock.

Many hardware stores sell a spiral key extraction tool. This tool has a thin rod with spiral threads that can be placed in the keyway, and then bent to form the broken part of the key. Once it is firmly anchored to the serrations, you can turn the bar in a circle and then pull it against the broken section of the key.

It's worth attempting to remove a broken master key before calling a professional locksmith. If you're unable to take the broken piece off, you'll need to contact a professional locksmith. A locksmith can give you a new key that will be programmed with the transponder of your car.