12 Companies Leading The Way In Patio Door Lock Repair
Patio Door Lock Repairs
Over time, wear and tear can cause lock malfunctions. There are a few easy steps you can follow to ensure the security of your uPVC door.
These quick fixes will make your home safer no matter if you adjust the lock or clean the mechanism.
Clean the Lock
Patio doors are fantastic to let the outdoors in while keeping out the elements. However they can pose risky for security in the event that the lock isn't working correctly. Over time, wear and tear, hot and cold weather, dirt, tilt and slide patio door repairs debris can cause your patio door lock to become difficult to operate. With some minor maintenance you can make sure that your patio door's locks will always perform properly.
It is important to first clean the patio door lock as well as all moving parts. This will help get rid of any grime and coatings that may be preventing the lock from working as it should. Begin by wiping down the moving parts of the lock for your patio door lock repairs near me door using a damp cloth. then use a scouring pad or rough damp cloth to scrub any difficult-to-access parts of the door and frame that are covered in dirt. It is recommended to wipe the entire lock using a dry cloth to remove any remaining dampness and let it to air dry prior to applying it to the next time.
If your patio door is equipped with pin-tumbler locks you can lubricate it by applying powdered graphite to the key. You can also apply a Teflon oil like WD-40 Multi Use Product. This kind of lubricant is easy to apply, and doesn't break down with time. If you are unable to find the right lubricant to use with your lock, use a pencil with larger tip. Put the pencil in the lock, and shake it around to spread the graphite.
Sliding patio door tracks also require regular maintenance to ensure they're free of dust, dirt and other debris. They are particularly susceptible to snow, ice, and other debris that could cause them to get stuck or to bind. This can make it difficult for your patio door to open and shut.
Clean the track rails and rollers on sliding patio doors by removing any weather stripping that is damaged or dirty. Clean it, and then replace it. The same applies for rollers on patio doors, which can be cleaned and sprayed with a non-stick lubricant in order to allow them to move freely.
Lubricate the Moving Parts
uPVC french doors, like sliding patio doors, operate using 3-4 or occasionally five-point locking mechanisms, which include the handle and lock cylinder controlled by a key. These doors require maintenance, oiling of the moving parts. This can be done with the use of a thin oil but not WD40. This should be done at least once a year.
If the hinges aren't causing the problem, it could be that the door is not aligned. It could be rubbing or catching the hole of the strike plate in the frame. The solution is to take off the strike plate, and then use a sharp chisel to enlarge the mortise it rests in. This allows the latch to sit properly in the hole and prevents scratching or catching on the frame.
Once the cylinder is cleared of the way take a measurement of its width using an object or a piece of wood that can fit into the gap of adjustment screw above the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder. the inner measurement runs from the center of the adjustment screw until the end of the cylinder.
Check the lock's length
If your patio door latch is difficult to turn even after oiling and cleaning it's possible that it is not aligned with the strike plate. Verify that the door is in a balanced position, and if the hinge screws are in good condition. In many cases, moving the strike plate downwards or upwards could fix the problem.
Oftentimes, the problem occurs when the strike of the lock is too small for the latch to properly engage. In this situation, you need to widen the opening with an hammer and chisel. Then, test the latch to ensure that it doesn't rub against the jamb frame of the door or fall the frame.
You should identify the type mortise lock that you are using before you purchase an alternative. This can be done by looking at the faceplate and observing whether it is square or round. Then, look at the screw holes on the current lock and note the size of each. This will enable you to locate a replacement lock that is the exact same width and will fit into the hole that you already have.
You'll want to identify the mortise lock and examine it for any bends, scratches or other damage that requires to be fixed. A bent or damaged latch is more likely break than one that's not utilized often, so make sure to replace the lock with a brand new one that is secure if you find any signs of damage or wear.
After you've examined the lock and determined which type of replacement you need, it's time to start working on the actual repair. The spindle and handle must be removed from the patio door. Introduce the new handle. Begin by installing the handle inside, aligning it with the spindle, and then securing it in place by using the two screws or bolts which hold it. Once the handle's interior is in, install the handle on the outside and screw it in place as well. Once you have completed these steps, test the handles to make sure they open and shut easily and that the latch engages correctly with the strikeplate.
Check the Strike of the Door.
The door latch and strike plate are the two components of the lock that work together to ensure the latch secures the door. Misaligned strike plate and door latches can cause the latch to not latch the door in a proper manner. This problem is usually very easy to fix.
Check the holes for receiving of the strike plate to ensure they are clear of obstructions, such as dirt or plastic plugs. Remove the screws that hold the strike plate. This allows it to move horizontally, but it will not be able to separate from the frame. Adjust the strike plate so that it aligns its holes for receiving with latch hooks of the door latch. After the strike plate has been adjusted, tighten the screws and test the door to see whether it locks smoothly after the new adjustment.
Door strike plates can be difficult to locate for homeowners with who repairs sliding patio doors patio door frame repair doors, however they are essential for locking and unlocking your door. The metal plates are situated between the top and bottom jambs of your door, which are where they help support the latch. The door latch is inserted into the strike plate and forms an airtight seal. If the strike plate is damaged, rusted, or not properly installed, it could stop the latch from locking the door securely.
A misalignment between the strike plate and latch is the most common reason for the patio lock not to close or remain in place. The easiest method to check for this is to perform the "lipstick test." Apply some lipstick along the edge of the deadbolt, then apply masking tape over it. The lipstick will leave an impression when you close the door. This will reveal exactly where the latch meets the strike plate. If the mark is too high or low, you can adjust the strike plate.
If your patio door locks for sliding are not working properly they could be a problem in keeping your home secure from intruders. You must repair the issue as soon as possible. If you follow these steps, you can fix the lock on your patio door and restore its functionality in a matter of minutes.
