12 Companies Are Leading The Way In Fiat Panda Key Fob Replacement

Reasons Your fiat punto key replacement 500 Key Fob Won't Work

A key fob with the fiat panda key fob 500 number is a great way to unlock the doors and get started the car. However, there are many reasons the fob could stop functioning. This includes a dead battery or water damage, receiver modules issues, and interference.

This listing is for a NEW replacement fiat punto keys Flip Key Remote - look-alike Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob being inoperative. Modern key fobs only have only a limited range of operation and must be within a few inches of your vehicle to function. If you're not close to your vehicle when you press the key fob button the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery in the coin cell (Part number CR2032) with a brand new one from a reputable brand such as Panasonic, Duracell, or Energizer. They are usually available in your local hardware store or online.

After you've replaced the battery in the coin cell, you can test it by standing close to your fiat 500 new key cost uk 500 and pressing the buttons. The parking lights should blink and the key fob should operate the lock and unlock switches.

If your key fob still isn't working even after replacing the battery, there may be water damage which prevents it from communicating with the module inside your vehicle. Water damage can happen in a number of ways, ranging from the slightest splash to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice How To Open Fiat 500 Boot Without Key draw out the moisture. If this doesn't work, you will need to have the fob reprogrammed either by an auto locksmith or dealer.

Water Damage

While the fob has some rubber seals to keep water out of the electronic chip inside it, submerging it in the ocean or washing it locked keys in car boot fiat punto a machine can cause water damage. Saltwater can cause the circuit board to short and then end up dying. It's not a good thing to get the fob wet however, don't give it up in the event that you accidentally drop it in the water or don't remove it from your pants pocket.

Take the battery off first. Clean the electronic chip using isopropyl alcohol or another similar product and dry it thoroughly before replacing the battery. Next, test the fob to test if it works. If the fob doesn't work it could need to be reset. This is typically done by a professional or dealer auto locksmith.

If the key is newer and has never been programmed to your car It is likely that it needs to be replaced completely. This is a simple process that can be handled by a professional automotive locksmith. The locksmith will require the key to be cut to match your car's ignition. The locksmith also needs to reprogram the fob into the vehicle's system. It's a simple and cost-effective procedure that is usually completed in the next day.

Receiver Module Issues

Your 500 key fob might not work because it's out of range. The remote has a range of 30 feet, which means if you are too far from your car it won't respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds.

If you've replaced your coin battery (commonly known as a "button" or "watch") and the fob isn't working it could be due to an internal circuit board issue. Reprogramming the fob usually resolves this issue. The instructions are available for most vehicles on YouTube or in the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in their place. If they loose tension, it can prevent the coin battery from sitting properly and could cause the remote to malfunction.

In rare cases the fob could be out of alignment with your vehicle because of hardware or software problems. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances, they may need to reinstall the software on your body control module as well.

Interference

In addition to a dead coin battery The key fob might not be receiving or transmitting the signal due to interference. This could happen if the key fob is in proximity to a radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons the key fob could not function include a poor connection to the buttons or damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. replacing the battery, reprogramming it and using the spare key fob, you could have a damaged receiver module on your 500. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then read by the vehicle.

Fortunately, there's an easy way to reset all on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then reconnect the battery. This will clear out any remaining electricity and restart the car's computers. This could help the key fob to function again. If the issue continues, you should seek out an expert technician. They can identify the root cause of your problem.